jt33 tdlas gas analyzer 诊断代码
共 93 条诊断代码 · 来源手册 BA02297CZH_0324.pdf
对应产品：Analizador de gases （查看参数与选型）
| 代码 | 信号 | 简述 | 行为 | 页码 |
|---|---|---|---|---|
| C102 | C | Laser temperature sensor faulty | Warning | P112 |
| C104 | C | Laser temperature settling | Warning | P112 |
| C111 | C | Peak track adjustment warning | Warning | P112 |
| C113 | C | Auto ramp adjustment warning | Warning | P113 |
| C114 | C | Detector reference level delta rescrub exceeded | Warning | P113 |
| C301 | C | SD memory card error | Warning | P113 |
| C302 | C | Device verification in progress | Warning | P113 |
| C412 | C | Processing download | Warning | P114 |
| C431 | C | Trim 1 to n | Warning | P114 |
| C484 | C | Failure mode simulation | Warning | P115 |
| C485 | C | Measured variable simulation | Warning | P115 |
| C486 | C | Current input 1 to n simulation | Warning | P115 |
| C491 | C | Current output 1 to n simulation | Warning | P115 |
| C494 | C | Switch output simulation 1 to n | Warning | P115 |
| C495 | C | Diagnostic event simulation | Warning | P115 |
| C501 | C | Stream Change Comp. (SCC) config. faulty | Warning | P115 |
| C502 | C | Measurement calculation timeout | Warning | P115 |
| C594 | C | Relay output simulation | Warning | P115 |
| C902 | C | Spectrum clipped | Warning | P116 |
| C903 | C | Validation active | Warning | P116 |
| C906 | C | Enclosure temperature spike | Warning | P116 |
| C922 | C | Scrubber protection active（洗涤器保护激活） | Warning | P117 |
| F082 | F | Data storage | Alarm | P112 |
| F083 | F | Memory content | Alarm | P112 |
| F100 | F | Laser off | Alarm | P112 |
| F101 | F | Laser off | Alarm | P112 |
| F103 | F | Laser temperature unstable | Alarm | P112 |
| F105 | F | Cell pressure connection defective | Alarm | P112 |
| F106 | F | Sensor (Optical Head) faulty | Alarm | P112 |
| F109 | F | Peak index @1 out of range | Alarm | P112 |
| F110 | F | Peak track adjustment exceeded | Alarm | P112 |
| F112 | F | Auto ramp adjustment exceeded | Alarm | P113 |
| F201 | F | Device failure | Alarm | P113 |
| F242 | F | Software incompatible | Alarm | P113 |
| F252 | F | Modules incompatible | Alarm | P113 |
| F262 | F | Sensor electronic connection faulty | Alarm | P113 |
| F270 | F | Main electronic failure | Alarm | P113 |
| F271 | F | Main electronic failure | Alarm | P113 |
| F272 | F | Main electronic failure | Alarm | P113 |
| F273 | F | Main electronic failure | Alarm | P113 |
| F275 | F | I/O module 1 to n defective | Alarm | P113 |
| F276 | F | I/O module 1 to n faulty | Alarm | P113 |
| F283 | F | Memory content | Alarm | P113 |
| F300 | F | Sensor electronics (ISEM) faulty | Alarm | P113 |
| F304 | F | MAC electronics connection faulty | Alarm | P114 |
| F305 | F | Solenoid @1 trigger error | Alarm | P114 |
| F306 | F | Heater temperature sensor | Alarm | P114 |
| F307 | F | Heater connection error | Alarm | P114 |
| F311 | F | Electr. failure | Alarm | P118 |
| F331 | F | Firmware update failed | Alarm | P114 |
| F332 | F | Writing in HistoROM backup failed | Alarm | P114 |
| F361 | F | I/O module 1 to n faulty | Alarm | P114 |
| F372 | F | Sensor electronics (ISEM) faulty | Alarm | P114 |
| F373 | F | Sensor electronic (ISEM) faulty | Alarm | P114 |
| F375 | F | I/O – 1 to n communication failed | Alarm | P114 |
| F382 | F | Data storage | Alarm | P114 |
| F383 | F | Memory content | Alarm | P114 |
| F387 | F | HistoROM data faulty | Alarm | P114 |
| F410 | F | Data transfer | Alarm | P114 |
| F437 | F | Configuration incompatible | Alarm | P115 |
| F520 | F | I/O 1 to n hardware configuration invalid | Alarm | P115 |
| F803 | F | Current loop @1 | Alarm | P115 |
| F908 | F | Cell pressure dry rescrub | Alarm | P116 |
| F909 | F | Cell pressure delta rescrub | Alarm | P116 |
| F910 | F | Cell temperature delta rescrub | Alarm | P116 |
| F911 | F | Detector reference level delta rescrub | Alarm | P116 |
| F912 | F | Fit ratio 2 rescrub | Alarm | P116 |
| F913 | F | Fit ratio 3 rescrub | Alarm | P116 |
| F914 | F | Fit residue rescrub | Alarm | P116 |
| F915 | F | Peak tracking rescrub | Alarm | P116 |
| F916 | F | Auto ramp rescrub | Alarm | P116 |
| F920 | F | Fit residue too low | Alarm | P116 |
| M107 | ? | Detector zero range exceeded | Warning | P112 |
| M108 | ? | Detector reference level range exceeded | Warning | P112 |
| M232 | M | Real time clock defective | Warning | P113 |
| M303 | M | I/O @1 configuration changed | Warning | P113 |
| M311 | M | Electronic failure | Warning | P114 |
| M330 | M | Flash file invalid | Warning | P114 |
| M436 | M | Date/time incorrect | Warning | P114 |
| M438 | M | Dataset | Warning | P115 |
| M500 | M | Laser current out of range | Warning | P115 |
| M904 | M | Switch gas valve | Warning | P116 |
| M921 | M | Scrubber depleted（洗涤器耗尽） | Warning | P117 |
| S441 | S | Current output 1 to n | Warning | P115 |
| S444 | S | Current input 1 to n | Warning | P115 |
| S801 | S | Supply voltage（供电电压） | Warning | P109 |
| S832 | S | Electronics temperature too high | Warning | P115 |
| S833 | S | Electronics temperature too low | Warning | P115 |
| S842 | S | Process limit | Warning | P108 |
| S900 | S | Cell pressure range exceeded | Warning | P115 |
| S901 | S | Cell temperature range exceeded | Warning | P116 |
| S905 | S | Validation failed | Warning | P116 |
| S930 | S | Cell gas flow not detected（未检测到测量池气体流量） | Warning | P117 |
需要 jt33 tdlas gas analyzer 的备件或技术支持？
联系我们
，或致电 0755-82221901。