TriOxmatic® 701-15
Product Overview
-
Electro-chemical sensor to measure dissolved oxygen
-
The TriOxmatic® with 3 electrode system for the reliable oxygen measurement - patented know-how at low investment costs:
-
Reliable operation by proven technology
-
No run in, no drift: Stable measured values from the beginning to the end
-
Self diagnosis system SensReg/SensLeck by 3 electrode system
-
In the analog sensors of the TriOxmatic® series, you will find the ideal solution for your application. In addition to the continuous measuring accuracy, the sensors are equipped with an automatic self diagnosis system, a shorter response time and different cable lengths as options. Regardless of this, all models are supplied with accessories kits and can be connected to the monitor Oxi 298 (exception: TriOxmatic® 700).
-
TriOxmatic® 700 – predestined for the use in biological cleaning steps (wastewater treatment plants)
-
Universal oxygen sensor with high measuring accuracy and automatic self diagnosis SensReg (electrolyte consumption) and SensLeck (membrane monitoring). Based on its median response time of t90 < 180 s, the sensor is insensitive to air bubbles and therefore predestined for measurement and regulation of the oxygen content in biological cleaning steps of wastewater treatment plants. The TriOxmatic® 700 is alwo available as a salt water version.
-
Nur noch als Nachrüstarmatur für analoge Umformer der Serien Ecoline® und QuadroLine®. Als digitale Version weiterhin erhältlich (IQ SENSOR NET System 181).
-
TriOxmatic® 690 – suitable for pure measuring tasks in wastewater/water
-
Very economic model without self diagnosis. This makes this oxygen sensor suitable especially for pure measuring tasks in wastewater/water where a continuous membrane and electrolyte monitoring is not necessary.
-
TriOxmatic® 701 – increased resolution for the residual oxygen in the denitrification
-
Based on the increased resolution, a shorter response time (t90 < 30 s) and the thinner special membrane, this sensor can be used for quicker response processes with lower O2 concentrations (e.g. for the measurement of residual oxygen and the denitrification).
|
Model |
TriOxmatic® 690 |
TriOxmatic® 701 |
|
|
Order No. |
201690, 201692, 201693V |
201678, 201680, 201682V |
|
|
Measuring principle |
Electrochemical |
||
|
Measuring Range (25 °C, depends on respective controller) |
|||
|
O2 Concentration |
0.0 ... 60.0 mg/l |
0.00 ... 20.00 mg/l; 0.0 ... 60.0 mg/l |
|
|
O2 Saturation |
0 ... 600 % |
0.0 ... 200.0 %; 0 ... 600 % |
|
|
Resolution |
O2 Concentration |
0.1 mg/l |
0.01 mg/l; 0.1 mg/l |
|
O2 Saturation |
1 % |
0.1 %; 1 % |
|
|
Response time at 25 °C |
t90: 180 s |
t90: 30 s; t99: 90 s |
|
|
Minimum flow rate |
0.05 m/s |
0.23 m/s |
|
|
SensCheck |
– |
SensLeck, SensReg |
|
|
Temperature Measurement |
Integrated NTC, -5 °C ... +50 °C |
||
|
Temperature Compensation |
0 °C ... +50 °C |
||
|
Pressure Resistance |
Maximum 10 bar |
||
|
Ambient Conditions |
Operational temperature: 0 °C ... +50 °C; Storage Temperature: -5 °C ... +50 °C |
||
|
Electrical Connection |
Integrated connection cable with 7-pole screw plug (IP 65); electrical supply via WTW controller |
||
|
Electromagnetic Compatibility |
According to EN 61326 class B and FCC class A |
||
|
Certifications |
CE, cUL, UL |
||
|
Mechanical |
Membrane/ |
POM |
|
|
Housing shaft |
Stainless steel 1.4571 |
||
|
Protection Rating |
IP 68 |
||
|
Cable |
PUR |
PU |
|
|
Weight (without cable) |
Approx. 660 g |
||
|
Warranty |
2 years on defects in quality according to § 10 terms of conditions |
||
Case Studies
Municipal Wastewater Treatment · WTW — Stock Configuration Case
Customer Profile
The typical setting in Municipal Wastewater Treatment is the inlet, biological and outlet stages of a municipal plant. The measuring point is WTW; the focus is covering online and laboratory water analysis with WTW instruments.
Key Difficulties
Conditions are high solids and corrosive fractions, with large diurnal flow swings and, on top of that, effluent parameters drift and probes foul with sludge and biofilm, which a standard configuration cannot handle for long. The design therefore starts with selected by parameter set, range and digital sensor protocol.
Implementation
The scope ran through the stock channel: configuring from stock and delivered quickly. Technically it hinges on selected by parameter set, range and digital sensor protocol, and on these requirements: stable compliance with Grade 1A discharge limits and online data reporting.
Customer Benefit
In practice this means plug-and-play digital sensors that keep calibration when swapped, which cut the workload on the site maintenance team.
Food & Beverage · WTW — Stock Configuration Case
Project Background
The project covers dosing, pasteurising, filling and CIP stages. The work centres on WTW and the core task is covering online and laboratory water analysis with WTW instruments.
Operating Challenges
The medium and duty are characterised by syrups, dairy and beverages that scale easily, under strict hygienic requirements, and frequent cleaning demands instruments that withstand hot CIP/SIP caustic cycles. So WTW cannot be specified generically — it calls for selected by parameter set, range and digital sensor protocol.
Solution
The Ainstru engineering team worked through the stock channel: configuring from stock and delivered quickly. The configuration involves selected by parameter set, range and digital sensor protocol, with these requirements in view: food-safety and hygienic design per 3-A / EHEDG.
Results
Since start-up the system has run steadily; the practical result is plug-and-play digital sensors that keep calibration when swapped.
Chemical & Pharmaceutical · WTW — Stock Configuration Case
Project Overview
The site is reactors, metering vessels and finished-product tanks. The customer wanted WTW properly configured on the existing plant, with the aim of covering online and laboratory water analysis with WTW instruments.
Technical Challenges
What actually causes trouble is highly corrosive media with solvents and crystallisation, partly in explosive atmospheres, and corrosion plus Ex protection shortens instrument life and makes downtime costly. All of this means the WTW configuration has to involve selected by parameter set, range and digital sensor protocol.
Configuration
Supply and installation were organised through the stock channel: configuring from stock and delivered quickly. On site this meant selected by parameter set, range and digital sensor protocol, checked line by line against: Ex certification and GMP traceability of records.
Performance
After commissioning the outcome is plug-and-play digital sensors that keep calibration when swapped, and the readings are now used for process tuning.
Power & Energy · WTW — Stock Configuration Case
Site Conditions
This is a Power & Energy customer whose plant is at boiler feedwater, turbine condensate and FGD/DeNOx systems. The main task was covering online and laboratory water analysis with WTW instruments.
The Problem
The difficulty lies in high temperature and pressure with both steam and saline water; at the same time drift under high temperature and pressure, with very costly unplanned outages. Specification therefore means selected by parameter set, range and digital sensor protocol.
What We Did
We took a stock channel approach — configuring from stock and delivered quickly. Delivery was built around selected by parameter set, range and digital sensor protocol, with point-by-point checks on: compliance with power-industry codes and unit availability targets.
Operating Outcome
In service the system performs as intended — plug-and-play digital sensors that keep calibration when swapped, with routine maintenance falling noticeably.
