Technical Data
CompareWireless components
| Measuring Principle | WirelessHART |
| Function | Intelligent WirelessHART and/or Bluetooth® interface module for easy and fast connection to HART devices |
| Certification | Non-hazardous area, ATEX, IEC Ex |
| Input | One point-to-point with HART device |
| Output | WirelessHART and/or Bluetooth® communication interface, Operating frequency: 2.4 GHz (ISM band), Transmission range under reference conditions: WirelessHART communication - up to 200 m (656 ft), Bluetooth communication - up to 40 m (131 ft) |
| Auxiliary power supply / Loop power supply | Loop-powered 4 to 20 mA |
| Dimensions (wxhxd) | W x H x D: 146 mm x 42 mm x 42 mm (dimensions in mm 25.4 = 1 inch) |
| Software | Internal software for reading data from HART field devices and communicating over WirelessHART and/or Bluetooth® |
| Operation | Integral via DIP-switches, Cell Phone configuration via SmartBlue App and Bluetooth®, Field Xpert configuration via Bluetooth® or HART-modem, PC configuration via FieldCare and HART-modem, PC configuration via FieldCare and WirelessHART Gateway |
| Operating Voltage | 24 V DC (min. 4 V DC, max. 30 V DC): min. 3.6 mA loop current required for start-up Voltage drop if internal HART communication resistor is deactivated: 3.2 V in operation, < 3.8 V at start-up Voltage drop if internal HART communication resistor is activated (270 Ohm): < 4.2 V at 3.6 mA loop current, < 9.3 V at 22.5 mA loop current |
FieldPort SWA50 connects HART field devices and reliably converts the HART signal into an encrypted Bluetooth® or WirelessHART signal. Use the Endress+Hauser SmartBlue app or Endress+Hauser Field Xpert to configure FieldPort SWA50 and view the measured values and the status of the connected HART field devices. HART field devices can be connected to the Netilion cloud ecosystem via FieldPort SWA50 and FieldEdge.
Benefits
Connect FieldPort SWA50 to reliably transmit process measured values via encrypted Bluetooth® or WirelessHART communication
-
Easily upgrade all two-wire or four-wire HART field devices
-
All HART field devices can be easily connected to the Netilion cloud ecosystem
-
The adapter is loop-powered and does not interfere with the process signal
-
Easily query diagnostic information of the connected HART field devices via the wireless connection
Application
FieldPort can easily upgrade all two-wire or four-wire HART field devices and can be installed in hazardous and non-hazardous areas. FieldPort SWA50 is equipped with a stainless steel housing, is robust and durable, and can be used in demanding operating conditions.
Spare Parts & Accessories 1
1 spare parts · click to collapse
| Order code | Description | |
|---|---|---|
| 71520242 | Mounting kit SWA50Mounting kit for tube or wall mounting- Usage: FieldPort SWA50. | Details |
Configurator / Comparison
Accessories / Spare parts
Source: Endress+Hauser public website information
Manuals & Documents 6
All documents for this modelCase Studies
Municipal Wastewater Treatment · Gateways and modems — Application Case
Project Background
The project covers the inlet, biological and outlet stages of a municipal plant. The work centres on Gateways and modems and the core task is converting field data into remote transmission channels.
Operating Challenges
The medium and duty are characterised by high solids and corrosive fractions, with large diurnal flow swings, and effluent parameters drift and probes foul with sludge and biofilm. So Gateways and modems cannot be specified generically — it calls for configured by protocol, tag count and carrier network conditions.
Solution
The Ainstru engineering team worked through the system components range: supplying as a full cabinet and signal-chain configuration. The configuration involves configured by protocol, tag count and carrier network conditions, with these requirements in view: stable compliance with Grade 1A discharge limits and online data reporting.
Results
Since start-up the system has run steadily; the practical result is remote sites can report back, making unattended operation possible.
Food & Beverage · Gateways and modems — Application Case
Project Overview
The site is dosing, pasteurising, filling and CIP stages. The customer wanted Gateways and modems properly configured on the existing plant, with the aim of converting field data into remote transmission channels.
Technical Challenges
What actually causes trouble is syrups, dairy and beverages that scale easily, under strict hygienic requirements, and frequent cleaning demands instruments that withstand hot CIP/SIP caustic cycles. All of this means the Gateways and modems configuration has to involve configured by protocol, tag count and carrier network conditions.
Configuration
Supply and installation were organised through the system components range: supplying as a full cabinet and signal-chain configuration. On site this meant configured by protocol, tag count and carrier network conditions, checked line by line against: food-safety and hygienic design per 3-A / EHEDG.
Performance
After commissioning the outcome is remote sites can report back, making unattended operation possible, and the readings are now used for process tuning.
Chemical & Pharmaceutical · Gateways and modems — Application Case
Site Conditions
This is a Chemical & Pharmaceutical customer whose plant is at reactors, metering vessels and finished-product tanks. The main task was converting field data into remote transmission channels.
The Problem
The difficulty lies in highly corrosive media with solvents and crystallisation, partly in explosive atmospheres; at the same time corrosion plus Ex protection shortens instrument life and makes downtime costly. Specification therefore means configured by protocol, tag count and carrier network conditions.
What We Did
We took a system components range approach — supplying as a full cabinet and signal-chain configuration. Delivery was built around configured by protocol, tag count and carrier network conditions, with point-by-point checks on: Ex certification and GMP traceability of records.
Operating Outcome
In service the system performs as intended — remote sites can report back, making unattended operation possible, with routine maintenance falling noticeably.
Power & Energy · Gateways and modems — Application Case
Application Context
boiler feedwater, turbine condensate and FGD/DeNOx systems is a typical Power & Energy duty. The project started from Gateways and modems, focusing on converting field data into remote transmission channels.
Process Constraints
drift under high temperature and pressure, with very costly unplanned outages, and high temperature and pressure with both steam and saline water only amplify it. The Gateways and modems specification must therefore cover configured by protocol, tag count and carrier network conditions.
Delivery Approach
Delivery was handled as the system components range — supplying as a full cabinet and signal-chain configuration. Execution centred on configured by protocol, tag count and carrier network conditions, together with compliance with power-industry codes and unit availability targets.
Field Results
Operation shows the benefit clearly — remote sites can report back, making unattended operation possible, with confidence in this measuring point improving markedly.
Related Products
Endress+HauserWirelessHART Fieldgate SWG70
Endress+HauserFieldPort SFP20
Endress+HauserCommubox FXA195
Endress+HauserWirelessHART Adapter SWA70
Endress+HauserSmart Ethernet gateway
Endress+HauserFieldgate FXA42
VEGAVEGA Tools app
Endress+Hauser